Showing posts with label DIY. Show all posts
Showing posts with label DIY. Show all posts

Sunday, October 19, 2014

Introducing Belle

Belle is a new shape in my line of pottery cuff beads.  Why Belle? Much like a Southern Belle, this shape of pottery cuff bead is beautiful, with a flirtatious curve to hug your wrist.  She is also flamboyant in size much like the Southern Belles' hooped skirts and wide brimmed hats.  The bead is approx. 1 inch by 2 and 1/2 inches.  Available in many colors and textures. 
Aqua Fresca

Purple

Blueberry

TuTu Tango


Tamale Red

This design is by MagpieARTicles on Etsy, she used a 3 piece set for the pendant designs below. and added accent beads and antique brass chain.  Send me photos of what you create using my beads and I will post them on an upcoming blog. 


Tuesday, March 18, 2014

Wonderful tutorial using Captured Moments Pottery Beads

Claire Lockwood is a guest blogger on Art Bead Scene today and has posted a great tutorial for making a flower bracelet. She has step by step directions on how to make this design, including all the pieces she used and where to find them. Claire is from Frome, England, in the United Kingdom.  She has a cute shop at Etsy visit here there to see her beautiful pieces.  I hope you enjoy her beautiful designs.  Go to Art Bead Scene Blog to see all the details.



Monday, February 17, 2014

Recycled Brighton Tin Cuff Bracelet and Earrings

     I just wanted to share a quick how to make a cute cuff bracelet and earrings out of an old tin.  I started with a Brighton tin that I had and first cut off the sides with a pair of tin snips so that I could use the flat part of the tin.  The tin was not very large but I was able to cut a nice 2 inch strip and some basic rectangles for a pair of earrings to match.
      For the cuff I used an aluminum cuff I had purchased some time back but a brass cuff would work also.  I aligned the tin to the cuff and punched holes with a metal punch to attach the tin using micro screws and nuts.  I then filed the extra length of the micro screw so that it was flush with the nut.  I added a few of my mini pottery flower beads for accents using the micro screws and a daisy spacer bead for a nice finished look.


      For the earrings I attached two jump rings and earring wires to the top of the tin and added a daisy spacer bead for detail.  I punched a hole at the bottom of the earrings and added a mini flower pottery bead and a daisy spacer bead and used cold connection with a micro screw and nut to secure on the back of the earring.  I then filed the screws flush with the nut for a nice finished effect.  The whole project took me about 20 minutes to complete and are a fun way to use a recycled tin.  I hope you enjoy the tutorial and make yourself something fun today.
 

Sunday, January 12, 2014

Thrift Store Find

I love going to the thrift store and looking at the cast offs that other people donate.  I am always on the look out for something to reuse.  This week I found a cool leather belt with a punched hole design, it was $1.50. I then went to the craft store and bought some turquoise braided ribbon and I was ready to create. 
 I cut 7 inches off the end of the belt, as I have a larger wrist, you might use more or less depending on wrist size.  I then began to sew or whip stitch the braided ribbon thru the existing holes.  I did have to cut the end off once and heat with a lighter to help the ribbon go thru the holes easier.
 Notice in the above photo where the arrow is pointing is the middle of the leather where I marked it with a pen before starting. 
 When I got around both sides and to the last end I tucked the ribbon under the last few stiches and did the same on the other side.
 Above you can see how the ribbon is unraveled some and I am tucking it under the existing stitches.
 A view of the other side so you can see one side finished and the other almost finished.
Above is the back of the belt where I tied a knot in the waxed linen thread to hold the bead on to the belt.
 I then sewed one of my pottery cuff beads thru the existing holes with waxed linen thread, if needed I could have punched holes.  On this one I lucked out as they were already there.
 The above photo show the cuff sewn on both sides.

 I had to punch one hole to add jump rings and a lobster claw but was able to use the existing hole on the other side.

 I made a quick pair of earrings and just attached the beads to ear-wires with jump rings and added a tiny copper bead for an accent.
 I simply threaded leather into one of my doughnut beads for a simple choker.  And tied a sliding knot to put on and off.
 These beads are in a Tahitian Blue they have a real water color effect which is fun for casual wear.
A close up of the earrings.

I wonder what people make of the loads of stuff I donate yearly to the thrift store? I think it is nice that we have the stores in our town, they benefit great causes and they are a great resource for items to reuse.  It is so much fun to find a treasure like the belt I found.  The best part is I have a large section of the belt left for another project and my daughter has already spoken for they next seven inch cut.  :)

More Show and Tell:

The following pieces were made by Carrie Grabowicz.  Carrie is a stay home mom of two sweet boys with lots of energy who love to have fun.  Her shop name Hammi Jammi came from a nick name she gave her boys when they were acting silly.  Carrie states that "It started off that they were "hams" if they were goofing around. Then it turned into "hambone jambone" and finally it turned into "hammi jammies."  What a fun name to use for her shop and a sweet sentiment behind the name.
 A beautiful design using one of my lavish steampunk beads.

 The above was made with an Elli bead in Autmun, the design below is also the Elli bead with flowers in Aqua Fresca.

Thursday, August 8, 2013

Leather Cuff Using Recycled Upcycled Leather Tutorial

Free Tutorial, this is so easy you can make it today and wear it today. :)

Supplies: 

1. Find an old belt that doesn't fit anymore or one from a thrift store.  Cut off approx. 7 1/4 inches of the leather (for a large cuff-less if your wrist is smaller).  Most belts will make 3-6 cuff bracelets or more depending on the size of the belt and the cuffs you make.
2.  Choose a great pottery focal bead.  I have several 100 to choose from I used the 30x60 mm cuff bead.
3.  Gather your leather punch, an ice pick would work also (just be careful).
 4.  Micro screws are used to cold connect (Cold connection refers to the process of joining together two pieces of metal without the use of heat) the pieces. I use a screwdriver to attach the screws like one you would use to repair eyeglasses.  The ends of the micro screws can easily be cut off if too long using wire cutters, and filed if needed with a household file to debur the edges.  I will often put a tiny drop of glue to make sure the screws do not loosen as the cuff is worn.
Stainless steel micro screws and nuts
 5. A pair of decorative ends in sterling silver plate.
These are reversable
Directions:

1. Cut the leather to size about 7 inches.
2. Hold the decorative end to the top end of the leather and mark where the screws will go.  Punch with leather punch.
3.  Attach decorative end using the micro screws and nuts.  Trim excess if needed with wire cutters.

One side attached to the decorative end
The back of the cuff

4.  Repeat with other side and attach a jump ring to one side and a lobster claw to the other side.
5.  Choose a cuff bead and mark the center placement on the leather using a pencil to indicate hole placement.  Make holes with leather punch and attach with micro screws and nuts thru the top of the bead, down into the leather, and finishing in the back with the nut.  Trim screw if necessary with wire cutters.  The screw should hold the bead to the leather but do not over tighten as you could break the bead. 

The back of the cuff before the screws were trimmed with wire cutters
 The finished bracelet, so cute and so easy.  How many will you make?

Leather cuff with pottery cowgirl bead
 I hope you enjoy creating with this free leather cuff and pottery bead tutorial.

Tuesday, July 23, 2013

Tutorial for Leather Cuff Bracelet

Honey Brown Mixed Media Cuff



This bracelet was accepted to be in the October Issue of Bead Trends.  Unfortunately, they are no longer publishing the magazine, so they sent it back to me.  Here is the tutorial I hope you enjoy making one similar.

The Inspiration:

Inspired by the love of vintage, this mixed media cuff features 2 vintage metal findings and a pottery bead in a metallic golden brown.  The pottery bead used on this cuff was handmade by me and is named after the most beautiful woman I know, my mom Zephyr.
The leather cuff is made using a cold connection process with micro screws.  A love of antiques and all things old becomes a show piece cuff bracelet.



Supplies:
Copper Brown Pottery Zephyr Bead from www.CapturedMoments.ETSY.com
2 Antique Victorian style brass stampings https://www.etsy.com/shop/2VintageGypsies
Leather 4x9 inch piece from Michaels
DIY Metal Jean Button Sewing Dept. of Michaels
6 brass daisy beads
6 micro screws and nuts www.CapturedMoments.ETSY.com
Leather Punch
Scissors
Hammer
Wood block
Small screw driver

Instructions:
1. Cut leather to 1 3/4x 9 inches, or smaller to fit your wrist.  Add jean button by punching a small starter hole at one end of the leather approx ½ inch from the end and centered.  Put the top ½ of the button through the top of the leather in to the punched hole and put the bottom ½ of the button on the bottom side of the leather aligning with the button top.  Place top side down on a block of wood and hammer it once or twice to secure.  Punch a small hole in the center of the other end of the leather ½ each from the end, and another at 1 inch from the end.  Cut down the center of the two holes to make a button hole for the jean button.
2. Determine the mid point of the leather, place the pottery Zephyr bead at the mid point and mark on the leather where the holes are.  Make a tiny hole with a leather punch, and then add a daisy bead and a micro screw thru the bead and secure on the back with a micro nut.  You could add E-6000 before attaching the screws for a more secure fit.  Repeat on the other side.
3. Attach a antique brass finding on either side of the pottery bead using the micro screw and daisy bead, securing on the back with a micro nut. The back of the micro screw can be sanded with a file if it is too long.

Saturday, May 25, 2013

Leather and Pottery Cuff Tutorial

I recently explored the possibility of making my own leather cuffs as I wasn't able to find what I wanted.  I found that both my local craft stores (Michael's and Hobby Lobby) sold leather strips (in the leather section of the store) that are approx. 4x9 inches.  I also found that in the sewing department I could purchase metal buttons that are designed for jeans.  The process was really easy, just cut the leather to the width you need and the length plus one inch to the length.  
Leather Punch

I have a leather punch that I used to punch a small hole in about 1/2 inch from one side and centered.
Metal button back

This shows the nail head of the metal button

Put the nail head of the metal button into the hole and then flip over the leather and line up the decorative metal button top, carefully flip over again and put the button back on a hard surface.  
 
This is the top of the decorative jean button

 With one good whack of the hammer it will be attached firmly to the leather.  On the other side of the leather I made two small holes parallel of each other and cut the center to form the button hole for the cuff.
Give the back of the button a whack or two with your hammer

The button is now attached

This is what it looks like buttoned
 Now embellish the cuff with old findings and a pottery bead. Determine the mid point of the leather, and align a pottery bead on a metal finding.  It helps if the metal is curved, just take a can of veggies out of the pantry and use it to curve the metal.  Line up the bead with the metal finding and mark on the metal finding where the holes are in the pottery bead.  Punch a hole thru the metal where you made your marks.  I use my euro punch to punch the metal but you could use a drill also.
My Euro Punch

Now line up to the mid section of your leather cuff and mark where the holes will hit the cuff.  Make a tiny hole with a leather punch, and then add a micro screw thru the pottery bead, finding and leather secure on the back with a micro nut.  You could add E-6000 to the back of the metal finding before attaching the screws for a more secure fit.  

This cuff was made with one of my Edith beads


I love the patina on the metal

This image shows the micro screws on the inside of the cuff.  The back of the micro screw can be sanded with a file if it is too long.


This image shows all the details of the cuff assembly

Another version using black leather and one of my pottery rose beads


These are so easy to make and the varieties could be endless using old findings and pottery beads.  I hope you enjoyed the tutorial.  Happy day! Cindy